Error Code P0613: What It Means & What To Do?

<<See All OBD Codes

Do you feel problem with the transmission? Are you facing erratic shifts and sometimes feel engine stalling and not running properly? All these may be due to transmission control problems and thus may lead to OBD code P0613 getting stored in the system along with other faults code in relation to transmission problems.

OBD-II Code P0613 is defined as a Transmission Control Module Processor Error

OBD fault code P0613 is a generic code that is universally defined as “Transmission control module (TCM) -processor error” on applications with automatic transmissions. Code P0613 is set when the PCM (Powertrain Control Module) or the TCM (Transmission Control Module), or sometimes both, detect a programming error, component failure in the TCM. On almost all applications, this code will set, and a warning light will be illuminated on the first failure, but take note that this code refers specifically to defects in, or failures of, the transmission control module, as opposed to general defects and faults in the transmission itself.

What causes this problem with the TCM Processor?

• Burnt, damaged, shorted, disconnected, or corroded wiring and/or connectors. Note that poor ground connections are a common cause of control module failures.
• Abnormal system voltages caused by defects in, or malfunctions of parts of the charging system
• Voltage spikes caused by improper jump starting can damage any controller, including the TCM and PCM
• Disconnecting the battery to “clear” unrelated codes or to “reset” the PCM can cause almost any controller to lose its programming and/or memory. Sadly, the TCM is often among the first controllers to suffer damage as a result of disconnecting the battery unnecessarily.
• Corrupted software. This sometimes happens when aftermarket performance settings are programmed into the PCM/TCM

1. Transmission Control Module - Faulty TCM is the main cause of OBD code P0613. Thus, replace TCM now!
2. Powertrain Control Module - Along with TCM, the PCM can also be at fault and can lead to P0613 getting stored and flashed in the system. Buy new module now!
3. Diagnostic Tools - Use professional OBD scan tools to diagnose an OBD code error problem. Buy quality diagnostic tools from us now!
4. Speedometer - Sometimes the speedometer can also be defective and indicating wrong information. Replace it now!

We at Parts Avatar Canada care for our customers, and that’s why we will help you to diagnose P0613 code by listing out some major symptoms. They are mentioned below as follows:

Common Symptoms

• Erratic transmission shift patterns
• Harsh transmission shifting
• Inoperable or inaccurate speedometer/odometer
• Other stored TCM/PCM codes What are some of the

Learn the ways with which you can correct this trouble code:

• Speedometer replacement
• TCM replacement
• PCM/ECM replacement
• CAN bus harness replacement
• Wiring and harness replacement

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of Powertrain Control Module, Speedometer/Odometer, Transmission Control Module, TCM harness and a lot more. We are sure that now all your issues would be resolved.

This code is related to P0614.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P0613 code to be stored:

• The first step that a technician should take is to use an OBD-II scanner to detect and verify the code.
• Once the P0613 code has been verified, they should inspect all the electrical wiring and connectors that connect the TCM to the PCM, and that are a part of the greater CAN.
• After repairing any loose, corroded, or shorted electrical components, the code should be cleared, and the system should be retested. If the P0613 is stored again, the mechanic has diagnosed an issue with the TCM.

Common Mistakes When Diagnosing the P0613 Code

Repairing the electrical components, or the faulty TCM itself, without checking for further issues is the most common mistake made when diagnosing OBD code P0613. Usually the fault in the TCM will not be registered until another issue requires the TCM to register some communication to the PCM. This means that there is another repair possibly needed, and by only addressing the immediate cause of the P0613 code, there could be a necessary repair going ignored. Also, examine all the faulty error code in the order in which they are stored in the system.

• Wiring and connector issues
• PCM and TCM error
• CAN harness and TCM harness faults