Error Code P0595: What It Means & What To Do?

<<See All OBD Codes

The trouble code P0595 can be defined as Cruise Control Servo Control Circuit Low.

P0595 fault code would start appearing when there is a low voltage problem with the cruise control servo control circuit in that the signal being sent to the engine computer is not within the specifications of the manufacturer.

This error code is related to a vehicle’s cruise control servo that would help a vehicle to maintain speed automatically. If the engine control unit detects voltage or resistance from the cruise control system, it will test the entire system - determining the cruise control servo control circuit is low on voltage to trigger up the P0595 error code.

What causes this problem with the Cruise Control Servo Control Circuit Low?

• There can be some faults in the cruise control servo
• Cruise control servo cable might be broken/stuck/disconnected/mis-adjusted
• Some wiring issues may exist
• The engine control module might be defective
• Module water intrusion
• Defaults in the connector

1. Cruise Control Switch - Do you remember when was the last time you got your car Cruise Control Switch checked up? A dirty Cruise Control Switch can cause a lot of issues like displaying P0595 code.
2. Engine Control Module - Are there some faults in your Engine Control Module? Don’t waste time and get them replaced or else P0595 code can turn up.
3. Cruise Control Relay - OBD Code P0595 can appear because of faulty Cruise Control Relay.
4. Throttle Position Sensor - Everything is fine with Cruise Control Relay and still P0595 code triggering? Then you must get your Throttle Position Sensor checked.
5. Powertrain Control Module - There can be some issues with the Powertrain Control Module due to which you may see P0595 code appearing over and over again. Visit us to buy best quality PCM online.
6. Coolant Temperature Sensor - A lot of issues can arise do to defective Coolant Temperature Sensor. Did you just see P0595 code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.

Our main motive is to achieve customer satisfaction and that’s why we will help you to diagnose P0595 code by mentioning some major symptoms below:

Common Symptoms

• Erratic cruise control operation
• Vehicle speed limited with cruise control active
• There can be Inaccurate vehicle speed setting when compared to desired or set speed
• Specific cruise control functions might be malfunctioning
• There can be inoperative cruise control 

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0595:

• If there are some faults in the cruise control servo solenoid, then it should be replaced
• Make sure that you replace the cruise control switch
• It is very important to restore the cruise control circuit wiring
• You can always replace the cruise control fuses

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of Fusion, Wheel Bearing, Oil Pump, Idle Air Control Valve, Brake Light, Rocker Arm, Starter Relay, Automotive Fuses, 15 Amp Fuse and many more. Now all your problems would vanish within no time. 

We include basic steps below but refer to a vehicle year/make/model/powertrain specific repair guide for specific steps for your vehicle

• The cruise control servos are mounted in the engine compartment somewhere. Most times, they are in close proximity to the throttle body, after all they do control vehicle speed using this. Now once it is located, you must do a general visual inspection
• Look at the cable, check for fraying, kinks, corrosion or any signs of malfunctioning. If the servo cable does not move freely when controlling the throttle, the ECM could interpret it as a performance issue
• It's important to check all the vacuum lines running to the servo itself
• Any cracked or deteriorated lines should be taken as a sign of your vacuum system's health so it is recommended to replace all of the vacuum lines involved as they are inexpensive and could save you from problems in the future
• On to the electrical side of things, verify the connector on the servo. Any broken tabs or loose connections should be repaired
• The harness may be running through tight areas and/or moving parts, so be aware of any chafing areas that could cause an issue and repair any broken/ damaged wires
• Depending on your OBD2 scan tool capabilities, you can potentially monitor the servo's operation with it connected to the vehicle
• Sometimes you may be given percentages or maybe electrical values. Either way you can compare the values to its physical operation by watching it under the hood, with the wheels off the ground
• This is an old procedure and may cause issues especially when talking about more modern vehicles
• That is the reason why you must always ensure any diagnosing/ repair procedures which are recommended by your vehicle's manufacturer

Common Mistakes When Diagnosing The P0595 Code

• Most of the mechanics do not carefully test the components and simply replace the parts which can turn out to be a big mistake