P0578 - OBD Trouble Code

<<See All OBD Codes

P0578 error code can be identified as Cruise Control Multi-Function Input "A" Circuit Stuck.

The P0578 trouble code would be detected when the powertrain control module would register some faults in the cruise control multi-function input circuit.

The cruise control system works with the PCM to monitor the vehicle speed when the cruise control is activated. Now if the PCM would detect that the speed of the vehicle is not being automatically controlled by the cruise control, then it would initiate a self-test of the system. If an abnormal voltage reading is detected in the cruise control multi-function input circuit during this test, then the P0578 trouble code would be stored in.

What causes this problem with the Cruise Control Multi-Function Input "A" Circuit Stuck?

• There can be some issues related to the wiring
• Defects in the multi-function/cruise control switch
• Connector malfunction like corroded pins, broken plastic tabs, swollen connector body, etc
• Fluids/dirt/grime in cruise control button/switch might cause abnormal mechanical operation
• Faults in the engine control module

1. Engine Control Module - Did your mechanic just found out that there is some fault in the Engine Control Module? Buy top notch Engine Control Module from us at economical prices.
2. Cruise Control Switch - A broken Cruise Control Switch can cause a lot of issues. It would be nice if you get it replaced on time.
3. Powertrain Control Module - Everything is fine with the Cruise Control Switch and still OBD code P0578 flashing? Then there is definitely some fault with the Powertrain Control Module. Get it checked and replace if needed.
4. Fuel Injection Harness - Fuel Injection Harness is an important car part which should never be neglected. May be there is some fault in it due to which P0578 code may start flashing.
5. Fuel Injector - A faulty Fuel Injector can be troublesome. You can always rely on us as we have best auto parts for our customers.

We care for our customers and that’s why we can totally understand your problem. That’s the reason why we have listed out some major symptoms behind the flashing up of OBD Code P0578. They are mentioned here as follows:

Common Symptoms

• Illumination of the cruise control light regardless of switch position
• The cruise control cannot be set to desired speed
• There can be unusual vehicle speeds with cruise control active
• Cruise control might not function properly

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0578:

• It is very essential to replace the cruise control switch
• If there are any faulty electrical components, then they should be replaced or repaired as per the need
• Carefully replace the burnt fuses

Now are you thinking that from where will you purchase these car parts? You have arrived at the right place. We at Parts Avatar care for our customers, that’s why we provide best quality of engine light flashing, ratchet straps, tie down straps, body control module, blown fuse, battery connectors at marketable prices.

Do you wish to diagnose P0578 error code easily? Here are some steps which you should follow in order to diagnose this fault code:

Step 1

Once your vehicle's multi-function/cruise control switch is located, then you must visually inspect it for any kind of contamination. It is very easy for plastic buttons/switches to get dirty/greasy/sticky causing them to malfunction and/or operate abnormally. Make sure that the mechanical operation of the switch is seamless and smooth. Any problem here should be addressed immediately. If your particular scan tool/OBD reader has the capabilities, feel free to observe the electronic operation of the switch through data stream

Just be sure to avoid spraying any cleaning solutions directly to the button. Lightly dampen a clean rag with either water, soap & water, dash cleaner, etc. and carefully remove the debris from the switch's crevices. An air powered blow gun will aid in removing debris without worsening the situation

Step 2

To access the connectors and harnesses involved within the cruise control/multi-function switch input circuit, there would be a need to remove some dash plastic/shrouds. Be delicate whenever working with plastic. Comfortable room temperatures always help with the ease of dash/interior plastic disassembly/assembly

If you can easily access the connector, you may be able to apply specific troubleshooting steps provided by your service manual. Switch testing will most likely involve recording electrical values using your multimeter. This may include operating the switch while recording and/or static testing. Refer to the specific make and model service manual for "diagnostic flow chart"

Step 3

A problem within the ECM is, most times, the last resort in diagnosis. It may be one of the most expensive electronic repairs you could do on your vehicle, so you should leave this to the professionals

Common Mistakes When Diagnosing The P0578 Code

• When a mechanic is diagnosing the P0578 trouble code, then the most common mistake is forgetting to disconnect the PCM and the cruise control module when testing circuit resistance
• Make sure to check the blown fuses before you start replacing any other auto parts