Error Code P052D: What It Means & What To Do?

<<See All OBD Codes

The error code P052D can be defined as Cold Start A Camshaft Position Timing Over-Retarded Bank 2. The variable camshaft timing position for an over-advanced camshaft timing is monitored by the powertrain control module during cold start up. If the camshaft timing will exceed a maximum calibrated value or might remain in an advanced position, then the test would fail.

Want to learn something more about this fault code? The vehicle’s engine ignition system, mechanical positioning of the rotating assemblies, fuel injection, emission systems, exhaust, transmission and many more are managed and monitored by the engine control module.

What causes this problem with the Cold Start A Camshaft Position Timing Over-Retarded Bank 2?

• Defective intake valve timing control solenoid valve
• The intake valve timing intermediate lock control solenoid valve is flawed
• The signal pick-up portion of the camshaft has accumulated debris
• The timing chain might be incorrectly installed
• Foreign matter may contaminate the oil groove for intake valve timing control
• There can be some defects in the crankshaft position sensor
• The camshaft position sensor might be faulty

1. Crankshaft Position Sensor - There can be some issues with the Crankshaft Position Sensor due to which you may see P052D code appearing over and over again. Visit us to buy best quality Crankshaft Position Sensor online.
2. Camshaft Position Sensor - A lot of issues can arise do to defective Camshaft Position Sensor. Did you just see P052D code flashing? Now you know the reason why it is appearing. Get it inspected and replaced on time.
3. Throttle Body - Faulty Throttle Body can be the reason why P052D code is flashing. Visit us to purchase top notch Throttle Body online.
4. Electronic Control Unit - It is an important auto part which needs full care. A faulty Electronic Control Unit can be a reason behind the flashing up of P052D code.
5. Timing Chain - OBD Code P052D can appear because of faulty Timing Chain.
6. Throttle Position Sensor - There can be some issues with the Throttle Position Sensor due to which you may see P052D code appearing over and over again. Visit us to buy best quality Throttle Position Sensor online.
7. Air Intake System Parts - Are you facing some faults in your Air Intake System Parts? Don’t worry and get them replaced or else P052D code can turn up.

You might be thinking that how would you diagnose these problems? We at Parts Avatar Canada would help you diagnose the major symptoms easily.

Common Symptoms

• The overall engine performance might be poor
• Some cold start issues
• Decrease in the fuel economy
• There can be possible misfire on start-up

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• Make sure to correct the faults in the intake valve timing control solenoid valve
• Restore the intake valve timing intermediate lock control solenoid valve
• You must install the timing chain correctly
• Replace the quirky crankshaft position sensor
• If there are some defects in the camshaft position sensor, then it should be replaced

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of powertrain control module, engine control module, Timing Chain Tensioner, VVT Solenoid, Cam Chain, Cold Air Intake, Timing Gear and many more. Now all your problems would vanish within no time.

Have a look at some steps which you should follow in order to diagnose this fault code:

• Check for any Technical Service Bulletins that could provide possible solutions for any problems since most vehicles have upgradeable software in their ECMs. If a replacement is required, it is best to use a brand-new factory ECM and to program the latest software
• This step will require you to take a trip to an authorized service center of the brand of your vehicle. Just remember that an ECM can easily be replaced when there was actually a defective engine sensor, which can be a result of an overlooked detail in the initial diagnosis
• This is the reason why professional technicians will follow some sort of flow chart when inspecting a trouble code to prevent a misdiagnoses. It's always a good idea to refer to your specific model's service information first
• It would be a good idea to test the camshaft leaks immediately as they can produce more issues down the road if left unattended. Refer to your service manual for specific diagnostic procedures as well as location of the components. Depending on what type of camshaft position sensor you have (e.g. Hall effect, Variable reluctant sensor, etc.), diagnostics will vary as per the make and model
• There should be power present at the sensor in order to monitor the shafts position. If found defective, replace the sensor, reset the codes, and then test drive the vehicle
• Given the fact that "cold start" is in the description of the code, you should probably take a look at your cold start injector. It also, may be mounted to the cylinder head and somewhat accessible. Injector harness' are extremely susceptible to drying up and cracking, due to conditions, causing an intermittent connection. And most likely a cold start issues as well
• Be very careful when you are disconnecting any injector connector, during diagnosing