Guide To P0527 OBD Error Code Solutions

<<See All OBD Codes

Puzzled? Don't know how to go about the Error Code P0527? Well, you don't have to care about a thing when Parts Avatar is here to mend of everything. So, to begin with, it is important to know that Cooling fans are used to cool the Engine temperature and the A/C system and are all controlled by the Powertrain control module (PCM). The fan speed sensors installed serve two purposes. Vehicles equipped with a fan clutch use the fan speed sensor to ensure the functioning of the fan. Also, vehicles with an electric fan make use of the fan speed sensor to make sure that fan speed coincides with the fan speed required by the Powertrain Control Module (PCM). the Powertrain Control Module is in charge of setting the optimum required by the fan. If a signal is received by the PCM via fan speed sensor indicating a fan speed that does not match the required speed, the diagnostic trouble code P0527 is set. The Engine light illuminates and there is also a possibility of a fault in the PCM/ECM.

The sensor in use is a 3 wire, hall effect sensor that uses a 5-volt reference source from the PCM, a ground wire and a signal wire to the PCM to control the fan speed. What actually triggers a P0527 DTC is the PCM detecting a mismatch. When the actual fan speed fails to match with the required or commanded speed, an error code P0527 is set.

What causes this problem with the Fan Speed Sensor Circuit Range/Performance?

• A defect in the engine coolant temperature sensor.
• Distorted, lose or burnt Engine coolant temperature sensor connector.
• Damaged cooling fan motor.
• Failure in the cooling fan relay.
• Broken or faulty fan clutch.
• Malfunctioning electric fan.
• Blown fuses.
• Inaccurate/damaged fan speed sensor.
• Fan speed sensor wires that are shortened, disconnected or corroded.
• Damaged, broken or weary or Fan speed sensor connectors.

1. Engine Coolant Temperature Sensor - Coolant Temperature Sensor is a sensor used to monitor the temperature of the Engine’ coolant. So, to maintain an optimal temperature, the coolant temperature sensor should be replaced/repaired immediately.
2. Fan Clutch - Get your Error Code fixed instantly with a new Fan clutch. Parts Avatar right place that provides the best fan clutches across the country.
3. Cooling Fan Speed Sensor - Having problems with the Cooling Fan speed Sensor? Don’t you worry, Parts Avatar has it all. A faulty CFS Sensor could end up being the originating point behind the Error code P0527.
4. Fan Speed Sensor Wire - disconnected or corroded wires should be replaced/repaired instantly to fight the Error code P0527. Looking for superior quality wires? Parts Avatar offers sustainable wires at pocket friendly prices available nowhere but directly your doorstep. Order now!
5. Fan Speed Sensor Connector - Facing the error code P0527? An inferior quality Fan speed sensor connector can always be hazardous for the system also it is one of the primal causes behind the occurring of the error code P0527. Tune into Parts Avatar for supreme quality Fan speed sensor connectors at economical prices.
6. Cooling Fan - A distorted Cooling fan can end up being the chief host inviting the Error Code P0527. So, replacing one can be one of the wisest decisions to avoid an erroneous system.
7. Cooling Fan Motor - Facing the Error P0527? Well, get that fixed with a new Cooling Fan motor available at Parts Avatar online at the prices you have been looking for.
8. Cooling Fan Relay - Facing the Error P0527? Well, get that fixed with a new Cooling Fan Relay at Parts Avatar available online at the best prices.
9. Fan Belt - Loosened or disconnected belts are one of the common causes leading to the Error Code P0527. Get yours changed now!
10. Powertrain Control Module - this integral unit, if damaged should be changed instantaneously as a PCM plays the main role in both inviting as well as detecting the Error Code P0527. So? Get yours changed now!
11. Engine Control Module - the ECM often regarded as the “brain” of the car should be changed immediately if broken or defective in order to avoid further problems caused due to an Error Code P0527.

It is essential to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P0527 here:

Common Symptoms

• Check Engine Light illuminated
• Overheating car
• The Air conditioners out of order.

Here are some ways with the help of which you will be able to correct the OBD Code P0527

• The Engine coolant temperature sensor should be repaired/restored.
• Also, the Engine coolant temperature sensor wires that are corroded, broken, or shortened should be replaced or repaired.
• The Engine coolant temperature sensor connectors that are damaged, loosened, or burnt should be changed.
• Defective Cooling fan motor should be replaced.
• Distorted Cooling fan relay should be changed or repaired.
• The faulty fan clutch should be replaced or repaired.
• Restore or mend the faulty electric fan
• Blown out fuses should be replaced.
• The faulty fan speed sensor should be replaced.
• Repair or replace fan speed sensor wires that are burnt, disjointed, or loose.
• The fan speed sensor connectors that are unsound, disconnected, or corroded should be mended or restored.

There is no need to be anxious as Parts Avatar – Car Parts Online is here to help you out! We have high grade Engine Coolant Temperature Sensor, Fan Clutch, Cooling Fan Speed Sensor, Fan Speed Sensor Wire, Fan Speed Sensor Connector, Cooling Fan, Cooling Fan Motor, Cooling Fan Relay, Fan Belt, Powertrain Control Module, Engine Control Module, Blown Fuse and a lot more for our precious customers.

• Diagnostic trouble codes should be diagnosed so that they tend to showup in the powertrain control module (PCM).
• An OBD-II scanner should be used to assemble all trouble codes that have been stored by the powertrain control module (PCM) as well as the freeze frame data.
• The cooling fan assembly wires should be investigated and all the frays, disjoints, and shortened edges should be replaced or repaired.
• Inspect the cooling fan assembly connectors. Repair and replace any corroded, broken or bent pins if found.
• The cooling fan assembly motor should be inspected and checked for proper operation and power supply. Replacements should be made if required.
• Check the fan motor relay and fuses. Amendments should be made as per the requirements.
• Clear all diagnostic trouble codes from Powertrain Control Module (PCM) and the vehicle should be retested to see if the P0527 diagnostic trouble code returns back.
• If the P0527 trouble code returns, the engine coolant temperature sensor should be checked if broken or disconnected. Repairs and replacements should be performed if necessary.
• Inspect the engine coolant temperature sensor connector for any sort of damages, corrosions or bent pins. Mend or change as demanded by the system.
• All the diagnostic trouble codes should be cleared from Powertrain Control Module (PCM) and the vehicle should be operated to see if the P0527 diagnostic trouble code returns.
• If the P0527 trouble code shows up again and the vehicle equipped with a high or low-pressure switch for the A/C or fan, will need a thorough check for proper operations.
• Clear all diagnostic trouble codes from Powertrain Control Module (PCM) and retest the vehicle again to see if the P0527 diagnostic trouble code sets again.
• If the P0527 trouble flashes back, the Powertrain Control Module (PCM) wirings should be checked and observed for sound workings. In a rare case, there could also be a PCM failure.

Common Mistakes When Diagnosing the P0527 Code

Scared of misdiagnosing the Error code P0527? Well, we have jotted down a few common mistakes committed while diagnosing the Error Code P0527.

The recurrent mistake made while diagnosing the DTC P0527 is when the cooling fan assembly is replaced while the real problem being in the fault relay, wirings or unsound fuses. It is essential to visually inspect all the components before performing the amendments with the cooling fan assembly.