P051B OBD Error Code: Problem & Solutions

<<See All OBD Codes

The P051B error code can be defined as Crankcase Pressure Sensor Circuit Range/Performance.

The crankcase pressure sensor signal is monitored by the engine control module. The trouble code P051B would be set up by the engine control module when the crankcase pressure sensor would not be as per the factory specifications.

Want to learn something more about this fault code? This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model.

What causes this problem with the Crankcase Pressure Sensor Circuit Range/Performance?

• The crankcase pressure sensor might be open or shorted
• There can be bad electrical connection in the crankcase pressure sensor circuit
• Issues related to PCV like broken runners/tubes, disconnected, chafed lines, etc
• There can be clogged PCV system
• Defective positive crankcase ventilation valve
• Flaws in the crankcase pressure sensor
• The crankcase pressure sensor might have some quirky
• Issue of internal electrical issue within the sensor
• The engine control module might not function properly
• Moisture present in the oil
• Problem of water intrusion
• The car engine might be filled with oil

1. Engine Wiring Connectors - A faulty Engine Wiring Connectors can be troublesome. You can always rely on us as we have best auto parts for our customers.
2. Engine Control Module - If everything is alright with Engine Wiring Connectors, then there is surely some defect in Engine Control Module. Get it replaced before the situation gets worse.
3. Crankshaft Position Sensor - P051B code can display due to some issues in the Crankshaft Position Sensor. So, it is very important to replace the Crankshaft Position Sensor with us at equitable prices.
4. Powertrain Control Module - Do you remember when was the last time you got your car Powertrain Control Module checked up? A defective Powertrain Control Module can cause a lot of issues like displaying P051B code.
5. Camshaft Position Sensor - OBD Code P051B can appear because of faulty Camshaft Position Sensor.
6. PCV System - Everything is fine with Camshaft Position Sensor and still P051B code triggering? Then you must get your PCV System checked.
7. Fuel Pressure Regulator - There can be some issues with the Fuel Pressure Regulator due to which you may see P051B code appearing over and over again. Visit us to buy best quality Fuel Pressure Regulator online.

There could be countless symptoms which that would accompany with this fault code. Willing to know some common symptoms of OBD Trouble Code P051B? Your wish is our demand. Have a look at them below:

Common Symptoms

• Smell of fuel can start coming
• Flashing up of the check engine light
• Unusual engine performance
• The fuel economy might start diminishing
• The gasket may start leaking
• The crankcase pressures might be high/low
• Appearance of the check engine light
• Sludge in oil
• Engine might be smoking black soot

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• Correct the issue of internal electrical issue within the sensor
• Replace the engine control module if it is not functioning properly
• Restore the positive crankcase ventilation valve
• If there are some faults in the crankcase pressure sensor, then you must replace it
• Make sure that the clogged PCV system is repaired properly
• You can always replace the crankcase pressure sensor if it is opened or shorted
• Carefully correct the problem of water intrusion
• Inspect the crankcase pressure sensor

Don’t get tensed if you are still facing any of these issues as we care for our customers and that’s why we offer a good range of o ring, diesel engine, Honda engine light, instrument cluster, shaft seal and a lot more. We are sure that now all your issues would be resolved.

It is essential to diagnose this fault code. Here are some steps which a mechanic should follow for diagnosing the problem that triggered a P051B code to be stored:

Make sure to do proper research of Technical Service Bulletins (TSB) for known issues with the specific vehicle in the troubleshooting process. Advanced diagnostic steps become very vehicle specific and may require the appropriate advanced equipment and knowledge to perform accurately.

We include basic steps below but refer to a vehicle year/make/model/powertrain specific repair guide for specific steps for your vehicle.

• You should open the oil cap on the top of the engine to inspect for any obvious signs of sludge build-up. Sludge can be caused by something as simple as a lack of oil changes, or following longer than recommended intervals
• A positive crankcase ventilation issue can cause moisture to enter the system causing sludge too. Either way, ensure your oil is clean and full
• You must keep this thing in mind to avoid overfilling the engine with oil. Do not start engine if this has happened, drain oil to bring level to an acceptable range
• Test the sensor by following manufacturer specific desired values from your service manual
• This usually entails using your multimeter and testing different values between pins. Record and compare findings to your make and model specifications. If anything is outside of specs, then you must replace the crankcase pressure sensor
• The crankcase pressure sensors are typically mounted directly to the engine block, the harnesses and wires involved, are routed through crevices and around extreme temperature areas
• You must be aware of this when visually inspecting the sensor and circuits. The fact that these wires and harnesses are subject to the elements, inspect for any hardened/cracked wires or moisture in the harness. Keep this in mind that the connector should be connected firmly and dry of any oil residue