Error Code P0405: What It Means & What To Do?

<<See All OBD Codes

P0405 is an OBD-II generic code which can be defined as Exhaust Gas Recirculation Sensor Circuit A Low. This code would start appearing when the engine control module would detect that the engine exhaust gas recirculation sensor has went below its specification range. There can be a short to ground of the sensor input to the ECM.

This trouble code is generic, which would mean that it can apply to all the vehicles which are equipped with the OBD-II or the vehicles which are made since 1996 up to the present. The specifications on the definition, the troubleshooting steps as well as repairs can always vary from one vehicle make to another.

What causes this problem with the Exhaust Gas Recirculation Sensor Circuit A Low?

• There can be shorted to ground EGR sensor return wiring or connection
• The EGR sensor 5-volt reference voltage might be open in the sensor or connection which may not make contact
• The EGR sensor return might be internally shorted to ground

1. Powertrain Control Module - The P0405 code can also arise due to some issues in Powertrain Control Module. So, it is advised to replace them as soon as possible.
2. EGR Valve Gasket - Do you remember when was the last time you got your car EGR Valve Gasket checked up? A damaged EGR Valve Gasket can cause a lot of issues like displaying P0405 code.
3. Crankshaft Position Sensor - Crankshaft Position Sensor is an important car part which should never be neglected. May be there is some fault in it due to which P0405 code may start flashing.
4. Engine Coolant Temperature Sensor - Is your Engine Coolant Temperature Sensor damaged or broken? Don’t worry as we have solutions for all your problems.
5. Fuel Pressure Regulator - Defective car Fuel Pressure Regulator can be a major reason why P0405 code depicts. So, make sure to replace it online so that you don’t have to face any further issues.
6. Air Intake temperature Sensor - Everything is okay with the Fuel Pressure Sensor and still OBD code P0405 triggering? Then there must be some defects in Air Intake temperature Sensor. Replace them as soon as possible.
7. Engine Control Module - Engine Control Module is an important auto part. Take care of it and you can rely on us to purchase best quality Engine Control Module online.

Willing to know some common symptoms of OBD Trouble Code P0405? Your wish is our demand. Have a look at them below:

Common Symptoms

• Illumination of the check engine light and the code might be set in ECM memory
• The ECM may disable the valve from opening when it sees a fault and the engine may have pre-ignition on acceleration
• The ECM might open the EGR valve more than needed if voltage is too low causing a stall or hesitation on acceleration
• The engine EGR system can cause the engine to run rough, hesitate, or even stall

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0405:

• You must repair the EGR position sensor after the wiring has been inspected to be okay
• Repair the wiring short to the EGR position sensor or connector signal return
• An open in the voltage reference to the EGR sensor should be repaired properly

There is no need to be anxious as Parts Avatar – Car Parts Online is here to help you out! We have high grade Throttle Position Sensor, Egr Valve Cleaner, Egr System, Egr Temperature Sensor, Egr Position Sensor and a lot more for our precious customers.

If you want to easily diagnose this fault code, then all you have to do is to follow the steps which are mentioned below:

• First of all the codes should be scanned and documents the freeze frame data in order to verify the problem
• Clears the engine codes and road test the vehicle to verify concern and codes comes back
• You should monitor the EGR sensor pad on a scanner to see if the sensor indicates the valve is in the correct closed position or the sensor voltage return is below specifications
• Remove the EGR sensor connector and you must inspect for corrosion in connector and clean if needed
• Inspect the connector if the 5 volts reference is getting to the sensor connection
• Connect the sensor reference voltage and signal return pins together and check the scanner to show reference voltage on EGR sensor pad
• Replace the EGR sensor or repair wiring as per the requirement and then recheck the system for proper readings

Common Mistakes When Diagnosing The P0405 Code

• The most common mistake which can occur is to not connect the sensor reference voltage and signal return pins together to see if all the wiring is fine before replacing the EGR position sensor
• The people simply start replacing the EGR position sensor which initially checking the wiring harness and connection to the EGR position sensor for shorts or open circuits