Guide To P0394 OBD Error Code Solutions

<<See All OBD Codes

This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model.

The P0394 trouble code can be described as Camshaft Position Sensor "B" Circuit Intermittent (Bank 2).

Want to learn something more about this fault code?

If the P0394 code is detected by the OBD-II scanner, then it would indicate that the powertrain control module has detected an intermittently incorrect voltage reading from the camshaft sensor circuit B in the engine bank 2.

What causes this problem with the Camshaft Position Sensor "B" Circuit Intermittent (Bank 2)?

• The engine fluid might be contaminated
• Defaults in the camshaft sensors
• The crankshaft sensors might have some flaws
• Faulty starter motor
• The car battery might be weak
• Faulty starting system circuit
• There can be opened or shorted wiring to the camshaft sensor
• Corroded or fluid-soaked connector/camshaft sensor
• Programming error in the powertrain control module
• The engine fluids might start leaking

1. Exhaust System Parts - A faulty Exhaust System Parts can be troublesome. You can always rely on us as we have best auto parts for our customers.
2. Powertrain Control Module - If everything is alright with Cylinder Head Gasket, then there is surely some defect in Powertrain Control Module. Get it replaced before the situation gets worse.
3. Cylinder Head Gasket - P0394 code can display due to some faults in the Cylinder Head Gasket. So it is very important to replace the Cylinder Head Gasket with us at equitable prices.
4. Ignition Coil - Do you remember when was the last time you got your car Ignition Coil checked up? A faulty Ignition Coil can cause a lot of issues like displaying P0394 code.
5. Camshaft Position Sensor - Bad Camshaft Position Sensor can cause a lot of difficulties, so why not get it replaced at time?
6. Engine Control Module - There can be some issues with the Engine Control Module due to which you may see P0394 code appearing over and over again. Visit us to buy best quality Engine Control Module online.
7. Crankshaft Position Sensor - Are you facing some faults in your Crankshaft Position Sensor? Don’t worry and get them replaced or else P0394 code can turn up.
8. Fuel Injector - Common cause behind this P0394 error code can be some fault in Fuel Injector. So it will be a good decision to replace them now.

It is vital to know the symptoms of an issue as only then you would be able to solve the problem. So that’s why we have listed out some major symptoms of OBD Code P0394 here:

Common Symptoms

• The car may not be able to start properly
• Vehicle cat start running roughly or may misfire
• Malfunction indicator lamp can start illuminating
• There can be loss of power

Looking out for some ways with the help of which you can correct this fault code? Then you have arrived at the correct place. We are here to help you out, so you must check out the steps mentioned below as follows:

• You must inspect and repair all electrical components
• The defected camshaft position sensor should be replaced
• Replace any wiring or electrical components
• The open or shorted camshaft position sensor should be repaired or replaced
• Recharging or replacing a dead or weakened battery
• Make sure to replace the defective starting system circuit
• Repairing or replacing a faulty starter motor
• The powertrain control module should be restored if found quirky

Parts Avatar Canada endeavours to fulfil all the needs of its consumer, that’s why we have a huge collection of top-quality electric battery, reluctor, automatic transmission module, injection and many more at equitable prices. We won’t let you down in any way.

Here are some steps which you should follow in order to diagnose this fault code:

• If the P0394 code has been verified with the scanner, the technician should perform a visual inspection of all the wiring, connectors, and other electrical components
• If any damaged elements appear, they should be replaced, reconnected, or repaired as necessary
• The mechanic should then clear the P0394 code from the PCM memory, and retest the system
• Now if the code returns, they will then move on to other repairs to address issues within the camshaft position sensor

Common Mistakes When Diagnosing The P0394 Code

• First mistake which technicians might make is that they may assume that the issue lies with a faulty sensor, and replace the part without performing a thorough diagnosis on the entire system. OEM sensor components don’t fail as frequently as other issues, and the code pertains to the entire circuit, which could indicate a fault at many other parts components