Guide To P0368 OBD Error Code Solutions

<<See All OBD Codes

The trouble code P0368 can be defined as Camshaft Position Sensor "B" Circuit High (Bank 1).

The exact rotational position of the camshaft can be measured by the camshaft position sensor. This would provide a critical data signal used by the engine control module to control the fuel injectors and ignition coils. Now when the powertrain control module would detect an irregular signal or sometimes no signal, then it would set P0368 trouble code.

This trouble code is generic, which would mean that it can apply to all the vehicles which are equipped with the OBD-II or the vehicles which are made since 1996 up to the present. The specifications on the definition, the troubleshooting steps as well as repairs can always vary from one vehicle make to another.

This can happen because of a lot of reasons and the mechanic should diagnose the specific cause for this code.

What causes this problem with the Camshaft Position Sensor "B" Circuit High (Bank 1)?

• Poor electrical connection in the camshaft position sensor circuit
• Faults in the starter motor
• There can be opened or shorted camshaft position sensor harness
• Defective starting system circuit
• Some quirks in the camshaft position sensor
• The car battery might be weak

1. Powertrain Control Module - Did your mechanic just found out that there is some fault in the Powertrain Control Module? Buy top notch PCM from us at economical prices.
2. Crankshaft Position Sensor - A broken Crankshaft Position Sensor can cause a lot of issues. It would be nice if you get it replaced on time.
3. Cylinder Head Gasket - Everything is fine with the engine control module and still OBD code P0368 flashing? Then there is definitely some fault with the Cylinder Head Gasket. Get it checked and replace if needed.
4. Camshaft Position Sensor - Camshaft Position Sensor is an important car part which should never be neglected. May be there is some fault in it due to which P0368 code may start flashing.
5. Ignition Coil - A faulty Ignition Coil can be troublesome. You can always rely on us as we have best auto parts for our customers.
6. Engine Control Module - P0368 code does not really end up spoiling your timing belt, but it might also accompany few Engine Control Module issues. We have best Engine Control Module with us.
7. Fuel Injector - Are you facing OBD Error Code P0368? Don’t worry as you can fix this issue with new Fuel Injector. We care for our customers, that’s why we have Fuel Injector for every make and model.

We care for our customers and that’s why we can totally understand your problem. That’s the reason why we have listed out some major symptoms behind the flashing up of OBD Code P0368. They are mentioned here as follows:

Common Symptoms

• Issue of lack or loss of power
• The car engine might start stalling
• Illumination in the service engine soon warning light

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P0368:

• Replace the camshaft and crankshaft sensors if found faulty
• If there are some faults in the starter motor, then it should be repaired
• Repair the weak car battery

Now are you thinking that from where will you purchase these car parts? You have arrived at the right place. We at Parts Avatar care for our customers, that’s why we provide best quality of electric battery, reluctor, starter motor, diesel injection at marketable prices.

Here are some steps which you should follow in order to diagnose this fault code:

• In order to diagnose this problem accurately, you will need specific tools, such as a digital volt/ohmmeter, a scanner, and an oscilloscope.
• Always begin with a careful visual inspection of your connectors and wiring, and be sure to replace or repair any damaged, corroded, or shorted wiring that you see.
• If there is an intermittent condition, then you can use the oscilloscope to monitor the waveforms created by your vehicle’s distributor, camshaft, and crankshaft sensors.
• Pay attention to glitches or inconsistencies, and search for areas of circuitry that appear to be contaminated with antifreeze, oil, or power steering fluid that has spilled from your car engine
• If you find that all your system reference voltage readings match up with the manufacturer’s values, you will need to replace both the camshaft sensor and crankshaft sensor

Common Mistakes When Diagnosing The P0368 Code

• The trouble code P0368 code pertains to the entire camshaft position sensor circuit. This would mean that it might not be your sensor, but something which is related to the sensor
• If you really want to pinpoint the real issue, then you will need to do a thorough diagnostic examination. In other words, do not automatically assume that when you see a P0368 code that you need to replace your camshaft sensor