P02F8 OBD Error Code: Problem & Solutions

<<See All OBD Codes

There are special transistors known as “drivers” in the engine control module to turn the fuel injectors on and off in the fuel injection system. If the powertrain control module would not be able to control the fuel injector for cylinder number three, then it would start triggering the P02F8 fault code.

The OBD code P02F8 can be described as Cylinder 11 Injector Circuit Range/Performance.

When the conditions are normal, then the engine control module would turn the fuel injectors ON as well as OFF in the fuel injection system. It is the engine control module which would set this trouble code when it would detect that the fuel injector is not working as it is designed.

This diagnostic fault code is a generic powertrain code, which means that it would apply to the OBD-II equipped vehicles. The specific repair steps can vary as it depends upon the vehicle make and model.

What causes this problem with the Cylinder 11 Injector Circuit Range/Performance

• Some faults in the fuel injector 11
• The fuel injector 11 can be dirty
• The fuel injector 11 can be plugged
• The harness of fuel injector 11 might be opened or shorted
• Bad electrical connection in the fuel injector 11
• The engine control module might be malfunctioning

1. Boost Pressure Sensor - The P02F8 code can also arise due to some issues in Boost Pressure Sensor. So, it is advised to replace them as soon as possible.
2. Turbocharger - Do you remember when was the last time you got your car Turbocharger checked up? A damaged Turbocharger can cause a lot of issues like displaying P02F8 code.
3. Knock Sensor - Knock Sensor is an important car part which should never be neglected. May be there is some fault in it due to which P02F8 code may start flashing.
4. Spark Plug - Is your Spark Plug damaged or broken? Don’t worry as we have solutions for all your problems.
5. Intake Manifold Actuator - Defective car Intake Manifold Actuator can be a major reason why P02F8 code depicts. So, make sure to replace it online so that you don’t have to face any further issues.
6. Boost Pressure Gauge - Everything is okay with the Intake Manifold Actuator and still OBD code P02F8 triggering? Then there must be some defects in Boost Pressure Gauge. Replace them as soon as possible.
7. Powertrain Control Module - P02F8 code flashing? Get your Powertrain Control Module inspected from a mechanic.
8. Wastegate - Wastegate is an important auto part. Take care of it and you can rely on us to purchase best quality Wastegate online.

Willing to know some common symptoms of OBD Trouble Code P02F8? Your wish is our demand. Have a look at them below:

Common Symptoms

• Illumination in the service engine soon warning light
• Decrease in the overall engine performance
• There can be an increase in the fuel consumption

If you wish to correct this fault code, then you have to follow certain steps. Correcting a problem needs your careful attention. Here are some ways with the help of which you will be able to correct the OBD Code P02F8:

• First of all you must inspect the knock sensor
• Make sure that you repair or replace the boost pressure sensor
• If you find out some defaults in the turbocharger/supercharger, then it should be definitely replaced
• The defective spark plug should be repaired or replaced
• The faulty engine control module should be replaced

There is no need to be anxious as Parts Avatar – Car Parts Online is here to help you out! We have high grade shift solenoid, diesel injection, fuel injector tester and a lot more for our precious customers.

Here are some steps which you should follow in order to diagnose this fault code:

It is the loose or corroded connectors which are the cause of the electrical fault. There are a few cases where low voltage wiring can become shorted or open.

The majority of electrical problems can be alternator related, starter solenoid wiring, oxygen sensor wiring due to the close proximity to the exhaust and battery related. The majority of electrical work connects customer-installed items such as high-power stereos and other parts or equipment installed incorrectly.

• Make sure that you check the connector on the fuel injector properly. It is a plastic connector secured to the injector with a wire clip around the connector. Pull on the connector to see if it comes off easily. Then you must remove the wire clip and pull the connector off the injector.
• The harness connector should be inspected for corrosion or pushed out pins. Make sure the two blades are not bent in the injector itself. Correct any defect and apply dielectric grease and install the electrical connector.
• Then you must start the car engine and listen to the injector to ensure it is working. Use a long screwdriver to the injector and the handle to your ear and you can hear it clearly. If it isn't making a highly audible 'clicking' noise, it either has no electrical power to it or it has failed.
• If it is not clicking, pull the connector off the injector and check for power with a voltmeter. If there is no power, then it would mean the wiring to the fuel pump relay is at fault or has a loose connection. If it has power, probe both terminals on the harness connector and if the PCM injector driver is operating, the voltmeter will indicate rapid pulses. If you notice the pulses, then you must replace the injector.
• If the injector was operating, then it is either plugged or dirty. First of all you must clean it. The kit to flush the injectors is inexpensive and will benefit the remaining injectors, possibly preventing a recurrence. If the flushing fails to solve the problem, then there is a need to replace the injector.

Common Mistakes When Diagnosing The P02F8 Code

• Failure in the fuel injector
• There can be some issues related to wiring
• The fuel injection control module might start failing