Error Code P02BC: What It Means & What To Do?

<<See All OBD Codes

Is your vehicle’s fuel injector circuit open or shorted? Are you experiencing some faults in the oxygen sensor? Is there an issue of powertrain control module programming error? All these indicate problem with the fuel delivery system and the Powertrain Control Module, thus flashing OBD Code P02BC error.

The P02BC fault code can be defined as cylinder 9 injector restricted. The fuel injectors need a precise degree of fuel pressure to deliver an exact measure of fuel in a precisely sprayed to the combustion chamber of each cylinder. This precise pattern would demand that each fuel injector should be free of leaks as well as restrictions. The powertrain control module would monitor the factors like the degree of the fuel trim required as well as exhaust oxygen sensor data which are combined with crankshaft position and camshaft sensor to detect a lean condition.

What causes this problem with the Cylinder 9 Injector Restricted?

• The fuel injector might be defective or clogged
• The fuel injector circuit can be opened or shorted
• There can be some faults in the oxygen sensor
• Issue of powertrain control module programming error
• Failure in the mass air flow or manifold air pressure sensor

1. Fuel Injector - OBD Code P02BC can appear because of faulty Fuel Injector.
2. Fuel Pump - There can be some issues with the Fuel Pump due to which you may see P02BC code appearing over and over again. Visit us to buy best quality Fuel Pump online.
3. Oxygen Sensor - Are you facing some faults in your Oxygen Sensor? Don’t worry and get them replaced or else P02BC code can turn up.
4. Manifold Air Pressure (MAP) sensor - Common cause behind this P02BC error code can be some fault in the Manifold Air Pressure (MAP) sensor. So, it will be a good decision to replace them now.
5. Powertrain Control Module - Oxygen Sensor is perfectly fine but still but having that trouble code P02BC flashing? In such a situation your Powertrain Control Module might be faulty. Why don’t you think of getting that replaced?

Willing to know some common symptoms of OBD Code P02BC? Your wish is our demand. Have a look at them below:

Common Symptoms

• The engine performance might start decreasing
• The overall fuel efficiency can start reducing with the passage of time
• Delay in the engine start up
• The presence of stored rich exhaust codes
• Some misfire codes can also get stored

We have listed out some ways which would help you to correct the occurrence of OBD Code P02BC. They are mentioned here as follows:

• If you find out that there are some faults in the fuel injector, then make sure that you replace it immediately

There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of Air fuel ratio sensor, Crankshaft sensor, Injection pump, O2 sensor and many more. Now all your problems would vanish within no time.

If you find out that MAF or MAP related codes present, diagnose and repair those before you start attempting to diagnose this P02BC code.

You must begin your diagnosis with a general inspection of the fuel injection rail area. You must carefully inspect the outside for signs of corrosion and leakage. If there is heavy corrosion on the exterior of the fuel injector, or if it is leaking, suspect that it has failed.

If you find out that there are no obvious mechanical issues in the engine bay, there are several tools that will be required for an accurate diagnosis:

• A digital volt/ohmmeter
• A diagnostic scanner
• An automotive stethoscope
• A reliable vehicle information source

• The fuel pressure gauge should be used to test fuel pressure and compare it with manufacturer’s specifications. If fuel pressure is within specs, then you should proceed to Step 2. If fuel pressure is below minimum specifications, use the DVOM to test fuel pump relay and fuel pump voltage. If the fuel pump is being supplied with an acceptable level of voltage which is usually battery voltage, then you must remove the fuel filter and see if it is clogged with debris. If the filter is clogged, it should be replaced. If the filter is not clogged, then the fuel pump should be suspected for failure
• You should then access the injector connector and use the DVOM to test for injector voltage and a ground pulse. If no voltage is discovered at the injector connector, proceed to Step 3. If voltage and a ground pulse are present, reconnect the injector and use a stethoscope (or some other listening device) and listen to it with the engine running. An audible clicking sound should be repeated in regular intervals. If the sound is not present, or if it is intermittent, suspect that the injector for the cylinder. In both the conditions fuel injector should be replaced
• There are a lot of modern fuel injection systems which provide a constant supply of battery voltage to each fuel injector, with the powertrain control module supplying a ground pulse at the appropriate instant, to complete the circuit and result in a spray of fuel to the cylinder. Use the DVOM to test system fuses and relays for battery voltage. Replace fuses or relays as needed. The system fuses should be tested with the circuit under load
• If all system fuses and relays are working in a perfect condition and there is no voltage present, then you can always use your vehicle information source to trace the circuit. Chances are that it will take you to the ignition switch or fuel injection module. You must do the circuit repairs as per the requirement

Common Mistakes When Diagnosing The P02BC Code

• The spark plug might be damaged or contaminated
• Engine sensor can start failing
• A leakage in the exhaust can be a big mistake
• A failure in the fuel injector
• There can be some issues with the fuel pump
• Internal engine failure
• Powertrain Control Module software might have to be updated