P018E OBD Error Code: Problem & Solutions

<<See All OBD Codes

Are you facing the issue of illuminations in the check engine light? Some sort of defects in the fuel pressure sensor? Has the overall engine performance started decreasing? These are all the symptoms of P018E trouble code and if you are experiencing the same, then you must immediately get these fixed.

The fuel pressure is monitored with the help of fuel pressure sensor in the fuel system. This information is used by the fuel pump control module to adjust the fuel pump on time as needed. If there is no change seen in the pressure by the fuel pump control module from the fuel pressure sensor when the fuel pump is activated, then it would give rise to P018E trouble code.

What causes this problem with the Fuel Pressure Sensor 'B' Circuit Intermittent/Erratic?

• Defective Fuel Pressure Sensor 'B'
• Fuel Pressure Sensor 'B' harness may be opened or shorted
• Bad electrical connection with the fuel Pressure Sensor 'B' circuit 

1. Powertrain Control Module - Is your Powertrain Control Module damaged or broken? Don’t worry as we have solutions for all your problems.
2. Fuel Rail Pressure Sensor - Defective car Fuel Rail Pressure Sensor can be a major reason why P018E code depicts. So, make sure to replace it online so that you don’t have to face any further issues.
3. Fuel Pressure Sensor - Everything is okay with the PCM and still OBD code P018E triggering? Then there must be some defects in Fuel Pressure Sensor. Replace them as soon as possible.
4. Fuel Sender Connector - P018E code flashing? Get your Fuel Sender Connector inspected from a mechanic.
5. Fuel Pump - There can be some defects in the Fuel Pump due to which P018E code may come on again and again. Make sure to replace it or else you may have to face some major issues.

For us our customers are everything, and that’s why we will help you to diagnose P018E code by mentioning some important symptoms below:

Common Symptoms

• Illuminations in the check engine light
• The engine might become hard to start or does not start at all
• The issue of poor engine performance

Do you want to correct the Fuel Pressure Sensor 'B' Circuit Intermittent/Erratic Issue? If YES, then have a look at points mentioned below:

• The most important thing to do with the help of which P018E trouble code can be corrected is to replace the fuel pump

Don’t Worry if you still face any issues as then all you have to do is to visit us. We have top variety of best priced oil pressure sensor, shift solenoid, ECM and a lot more to help to fix your car problem.

Make sure that you have turned on the ignition. You must use a multi meter set to DC volts so that you can check for reference voltage which is usually 5 volts from the powertrain control module. You can do this by connecting the negative meter lead to ground and the positive meter lead to the sensor B+ terminal on harness side of the connector.

If you find out that no signal is present, then you must connect the meter set to ohms between the reference voltage pin on the fuel pressure sensor and the reference voltage pin which is present on the powertrain control module.

If you find out that the meter is reading out of limits, then it means that there is an open circuit between the powertrain control module and then the sensor should be located and repaired.

If a numeric value is read by the meter, then it means that there is continuity. Now if everything is good up to this point, you will have to inspect that is power coming out of the PCM. This can be done by turning the ignition on and set the meter to DC volts.

The positive meter lead should be connected to the reference voltage terminal on the PCM and the negative lead to ground. If there is no reference voltage from the PCM, then it means that there is some fault in the powertrain control module. There are very rare chances of powertrain control module going bad, so it would be a good idea to check your work once again.

Common Mistakes When Diagnosing the P018E Code

• There can be some failures with the powertrain control module
• The Pressure sensor can have some defects
• The issue of wiring can arise