P0185 - OBD Trouble Code
OBD Code P0185 - Fuel Temperature Sensor B Circuit Malfunction
The P0185 code can be defined
as fuel temperature sensor ‘B’ circuit malfunction. It is a generic OBD-II code
which would indicate that the fuel temperature sensor B is malfunctioning. The
sensor might not be within the specification or the fuel temperature or fuel
rail might be too high or too low
Learn More About OBD Error Code P0185
We
all are well aware that the modern fuel injection and the ignition system is a
complex coordination of the sensor readings as well as actuator outputs. The
main aim is to deliver the most efficient power. A number of sensors are used
by the engine control module to determine how much fuel to inject at any given
moment, thus making precise calculations which are based upon the air flow and
temperature, engine load and speed, driver demand as many others.
What causes this problem with the Fuel
Temperature Sensor B Circuit Malfunction?
- Faults in the fuel temperature/consumption
sensor B
- There can be some issues with the ambient
temperature sensor
- Defective intake air temperature sensor
- Problem of open, shorted, or damaged wiring or
connectors
- A programming error in the powertrain control
module
Replace/Repair These Parts To Fix OBD Code P0185
- Fuel Temperature
Sensor - A lot of issues can arise do to defective Fuel Temperature
Sensor. Did you just see P0185 code flashing? Now you know the reason why it is
appearing. Get it inspected and replaced on time.
- Oil Pressure sensor - Faulty Oil
Pressure sensor can be the reason why P0185 code is flashing. Visit us to
purchase top notch Oil Pressure sensor online.
- Powertrain Control Module - OBD Code P0185 can appear because of faulty Powertrain Control Module.
- Diagnostic Tools - Willing to purchase some top-notch diagnostic tools online? We are here at your service.
Symptoms Of OBD Error Code P0185
It is vital to know the symptoms of
an issue as only then you would be able to solve the problem. So that’s why we
have listed out some major symptoms of OBD Code P0185 here:
Common Symptoms
- The vehicle won’t be able to start
because of frozen fuel from extreme cold conditions and water in the fuel
- If you find out that the fuel is too
hot and is boiling, then the vehicle will not start, may stall, or can start
losing power
- Erratic sensor readings can be caused because of excessive additives in the fuel and cause the fuel to boil off at lower temperatures which would cause the sensor to malfunction
- The engine control module sets code P0185 and check engine light would start illuminating
How To Correct P0185 Fuel Temperature Sensor B Circuit Malfunction
Want to correct the Trouble Code
P0185? Read these points mentioned below:
- Correct the fuel temperature sensor
and replacing it if it is out of specifications
- You must repair or replace a
defective connector or wiring to the sensor
- The diesel fuel heater assembly with
the temperature sensor should be replaced
There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of coolant temperature sensor, fuel tank pressure sensor, fuel sensor and many more. Now all your problems would vanish within no time.
Easy Diagnosis Of Engine Error OBD Code P0185
You must use a digital
volt-ohm meter and an electrical wiring diagram and repair manual to diagnose
faults in the FTS circuit and FTS. The FTS is situated in the fuel tank, as
part of the fuel sending unit, or practically anywhere else, before the fuel
injectors, in the fuel system. You can always check your manual for the precise
location of the FTS.
It can depend on the location of the ECM and FTS you may have to
work to get at their connectors, such as if located in the fuel tank under the
seat. One can start this diagnosis from the ECM or from the FTS, it would all
depend on what can be easily accessed.
- The first thing which you should do
is to scan the codes and documents the freeze frame data, after that the codes
should be cleared to verify if the code returns
- Perform a visual check of all the
wiring and connections to the sensor, checking for breaks in the wiring or
loose connections
- After that you should disconnect the
connection to the sensor and check to see if the sensor is testing within
specifications
- Then take a fuel sample to compare
the fuel temperature to the sensor input
- The diesel fuel heater should the tested
for proper operation to make sure it is working to heat the fuel without
overheating the fuel
Common Mistakes When Diagnosing The P0185 Code
- One of the most common mistakes can
be not doing a visual check of connections to the sensor to make sure they are
making good contact to the fuel heater and fuel temperature sensor
- Do not forget to check the fuel for
excessive additives that can cause sensors to malfunction