P0141 OBD Error Code: Problem & Solutions

<<See All OBD Codes

OBD error code P0141 is an OBD-II generic code. Thought its generic, the steps to resolve it might vary a bit depending upon the specific make and model. Your vehicle will flash this OBD error code when it has some issues with its O2 sensor. If you wish to know more about this error code, you can through our subsequent sections.

Do you know how O2 sensors work in your vehicle? Well, the oxygen sensors are meant to reach a min operating temperature of 750 degrees Fahrenheit to produce the required voltage sensor. To reach this required temperature, the heated oxygen sensor has a heater element in it. Your vehicle’s ECM keeps a check on the voltage signal from the heater element circuit and makes sure that the state of the circuit by comparing the voltage detected and the actual factory specifications.

OBD error code P0141 will set by your vehicle engine control module when it detects that O2 sensor heater circuits have a short or open circuit, or an excessive current draw in the O2 bank 1 sensor 2 heater circuit.

What causes this problem with the O2 sensor heater circuit (Bank 1 Sensor 2)?

• O2 wiring harness having a short to the ground or are open
• Heater element having an internal short or open
• High resistance of the O2 heater element
• High resistance of the heater circuit wiring

1. Oxygen Sensor - Oxygen sensor replacement on the list? If YES, then you have arrived at the right place. We have in stock for you high end oxygen sensors from top brands like Denso, Bosch and many more
2. Mass Air Flow sensor - Looking for top quality MAF sensor? If YES, you can find them with us for all makes and models.
3. Manifold Absolute Pressure Sensor - If you need manifold absolute pressure sensor to fix this problem, all you need to do is to browse through our website. You can find the most budget friendly parts with us.
4. Powertrain Control Module - There is a chance are that your PCM, itself is damaged and is demanding for a quick change. So, what are you waiting for? Buy a new one with us now.
5. Engine Control Module - Need to undergo ECM replacement? Worried about the cost? Well, you no longer need to worry about that as we have for you best priced ECM’S in stock.
6. Fuel Pump - We have in stock high end fuel pumps for all make and models for you. So, what are you waiting for? Make the best parts yours today.
7. Catalytic Converters - Looking for cat converters for your vehicle make? If yes, then you can easily find that with us.
8. Diagnostic Tools - If you need any of the DIY diagnostic tools, to diagnose the issues with your cars. You can find them all with us.
9. Spark Plugs - If you need spark plugs to fix this problem, all you need to do is to browse through our website. You can find the most budget friendly spark plugs with us.

Few of the common symptoms related to OBD error code P0141 are listed as follow:

Common Symptoms

• Poor fuel efficiency/economy
• Illumination of CEL (Check Engine Light)
• Foul smell from the spark plugs
• Engine misfires caused by defective spark plugs
• Rough idling
• Rich running of engine due to engine being in an open loop

Correcting a problem with your vehicle is not an easy job. You just don’t need to wish for it but you also need to work for it. You can get rid of this OBD error code if you follow few simple steps mentioned as follows:

As for all error codes, you will first need to clear the code and then perform a road test to verify if the code actually exists

Once you know the problem exists, you will have to undergo the following repairs or replacements:

• Repairing or replacing the defective Oxygen sensor for bank 1 sensor 2
• Replacing the damaged wiring and connectors to the o2 sensor for bank 1 sensor 2
• Changing the defective fuse to the heater circuit for the o2 sensor heater circuit

Now, after knowing the steps you also need to buy high end parts to fix or replace the damaged parts. If you are thinking from where to get it, you can easily browse through our website and get your hand on the top-notch auto parts today.

Once you detect that your vehicle is having some problem, next step is to make sure that you actually face that problem by undergoing a complete diagnosis for the same. We have listed out the steps to diagnose OBD error code P0141.

• First and foremost, you should check the connectors and wiring harness cover to the O2 bank 1 sensor 2
• Next, you should attach a scan tool to scan the codes and then freeze the frame data, after that clear the code to make sure that the failure exists
• Thirdly, check the o2 sensor data to see of the heater circuit is working for bank 1 sensor 2 or not
• Make sure that the O2 sensor heater circuit has enough power
• Now, check the O2 sensor heater circuit for the proper resistance to specifications
• For further diagnosis you will need to follow the manufacturer’s specific pinpoint tests

Common Mistakes When Diagnosing The P0141 Code

There are chances that while you conduct the diagnosis, you conduct some misdiagnosis too. And to avoid that we have here some guidelines to prevent those misdiagnoses.

• Make sure that you check the oxygen sensor wiring harness for any water entry in to the harness cover, that causes the sensor shorts.
• Also make sure that you check the O2 sensor for oil or coolant contaminants from engine leaks.
• Also, do make sure that everything works well after replacement.
• Also check the damaged defective catalyst by breaking the sensor or clogging sensor holes.