Guide To P012D OBD Error Code Solutions
OBD CODE P012D - Turbocharger/Supercharger Inlet Pressure Sensor Circuit High Downstream Of Throttle Valve
Is
there any issue related to powertrain control module? Or are you facing defects
in the turbocharger/supercharger inlet pressure sensor? The general efficiency
is reduced? If the answer to all these questions is a YES, then your vehicle is
definitely facing OBD P012D error. If there is malfunctioning in the turbocharger/supercharger
inlet pressure sensor, then the P012D error would start indicating
Learn More About OBD Error Code P012D
The
turbocharger/supercharger inlet pressure sensor which would tell the engine
control module how much air is being forced into the engine. If the PCM detects
that there is some incorrect signal from the sensor, then it will set P012D trouble code.
The
vehicle would be sent into the “limp home mode” due to this, which would limit
the amount of power out of the engine and would protect the other components
from getting damaged.
What causes this problem with the Turbocharger/Supercharger Inlet
Pressure Sensor Circuit High Downstream Of Throttle Valve?
- Defects
in the turbocharger/supercharger inlet pressure sensor
- Turbocharger/Supercharger
Inlet Pressure Sensor harness can be opened or shorted
- Turbocharger/Supercharger
Inlet Pressure Sensor circuit may start facing bad electrical connection
Replace/Repair These Parts To Fix OBD Code P012D
- Powertrain
Control Module - P012D code flashing? Get your
Powertrain Control Module inspected from a mechanic.
- Inlet Pressure Sensor - Do you
remember when was the last time you got your car Inlet Pressure Sensor checked
up? A damaged Inlet Pressure Sensor can cause a lot of issues like displaying
P012D code.
- Turbocharger - The P012D code
can also arise due to some issues in Turbocharger. So, it is advised to replace
them as soon as possible.
- Supercharger - Supercharger
is an important car part which should never be neglected. May be there is some
fault in it due to which P012D code may start flashing.
- Throttle Valve - Common cause
behind this P012D error code can be some fault in Throttle Valve. So, it will
be a good decision to replace them now.
- Intake Manifold - Are you facing
some faults in your Intake Manifold? Don’t worry and get them replaced or else
P012D code can turn up.
Need a tire or oil
change? Pick a service and time that's convenient for you at bookamechanic.ca today.
Symptoms Of OBD Error Code P012D
It is
very important to know the symptoms of an issue as only then you would be able
to solve the problem. So that’s why we have listed out some major symptoms of
OBD Code P004D here:
Common Symptoms
- Your
vehicle can start to enter limp mode
- Noises
may start coming from car engine
- Bad
overall performance
- Engine
may experience misfiring
- The
issue of stalling may arise
- Decrease
in the fuel mileage
How To Correct P012D Turbocharger/Supercharger Inlet Pressure Sensor Circuit High (Downstream of throttle valve)
Have a look at
some ways with which you can correct the P012D code:
- The damaged
turbo/supercharger inlet pressure sensor should be replaced
- There can be some
with the wiring harness, which can cause problems. So, you must get it repaired
or replaced
- If your car air filter system is clogged, then the best idea would be to replace it with a brand new one
There is no need to get strained if your OBD Code is still flashing up as we are here at your service. Have a look at our superior variety of air intake filter, fuel pressure sensor and many more. Now all your problems would vanish within no time.
Easy Diagnosis Of Engine Error OBD Code P012D
- Make sure that
you visually inspect the TCIP and surroundings. Since
we are aware about the nature of these fault codes, it makes us think that
there is surely some sort of physical problem causing this issue.
- Due to this you must check the harness thoroughly because the
harnesses for these sensors typically run along areas where extremely high
temperatures are present.
- You
must refer to Downstream of Throttle valve if you want to locate which sensor’s
circuit is malfunctioning. Downstream means after the throttle valve or the
side closer towards the intake manifold. The throttle valve is generally
mounted to the intake manifold.
- Once
the TCIP has been located, then the wires coming out of it should be followed
and you must inspect frayed/chafed/cut wires that may be causing an issue. The
location of the sensor depends on your vehicle make and model and you must have
enough access to the sensor’s connector. You can always disconnect it and
inspect the pins for corrosion.
- The
use of a circuit would totally depend on the make and model of your vehicle.
Locate the fuse boxes just about anywhere in the car.
- Some
of the good places where it can be placed are under the dash, behind the glove
box, under the hood, under a seat etc. Carefully locate the fuse and make sure
it fits within the slot tightly and make sure that it doesn’t blow.
- The other
step is to check your car air filter. There can be some signs of clogging or
dirtiness, so you must visually inspect your car air filter.
- You
must replace your auto
air filter if it is clogged or showing any signs of damage. This is surely a cost-efficient
way because air filters are inexpensive and easy to replace. You can always
check to see if your car air filter can be cleaned; in that case there would be
no need to replace it. Cleaning it would be a better idea than replacing the
entire assembly.
- If
you have checked out almost everything and still not able to find a
malfunction, then you must check the circuit itself. This may include
disconnect the ECM or PCM electrical connector so make sure your battery is
connected. You can always perform some basic electrical tests on the circuit.
- This
can be done by checking the continuity, check for short to ground, power and
more. If there is any kind of open or short, then it would indicate that there
is some problem and you will have to get it repaired.
Common Mistakes When Diagnosing the P012D Code
- Inlet
pressure sensor may experience some failure
- There
can be some faults in the powertrain control module
- Car
relay wiring issue may arise