Error Code P00AC: What It Means & What To Do?
OBD Code P00AC - Intake Air Temperature Sensor 1 Circuit Low Bank 2
The immediate signs of problem indicating OBD Error Code P00AC can the
Check Engine Light On, increase in the fuel consumption, smoke from the
tailpipe and increased heat level indications.
OBD-II Code Decreased
engine performance is defined as an Intake Air Temperature Sensor 1 Circuit Low
Learn More About OBD Code P00AC
The
IAT (intake air temperature) sensor is used to measures the temperature of air that enters
the engine. This temperature is important as the higher the intake air, the
higher the combustion temperatures. Higher temperatures result in increased NOx
(Nitrogen oxides) emissions.
To
control the increased combustion temps, the intake air tubing should be intact.
The IAT sensor measures air temp by using a thermistor which is supplied 5
volts reference voltage from the PCM (powertrain control module) and a ground.
The change in resistance changes the 5 V reference from the PCM, thereby
informing the PCM of the temperature of incoming air.
What causes the problem
with the IAT Sensor Circuit?
- Lack of reference voltage to IAT sensor
due to open wiring.
- Increased high intake air temperatures
- Signal circuit is short to ground
- IAT connector are damaged
- Faulty PCM that requires replacement or
reprogramming
Replace/Repair These Parts To Fix OBD Code P00AC
- Air Temperature
Sensor - The Air Temperature sensor if faulty will wrongly measure the air temperatures entering the engine,
thus affecting the combustion process. Thus, replacement of faulty sensor is in
order.
- Air Intake Kits - It is very important to maintain the proper air to fuel
ratio and enable proper functioning of the engine and thus no one can afford a
faulty air intake system. Buy quality air intake kits from us today.
- MAF Sensor - Mass Air Flow Sensors are an important component to the combustion
process and hampers the power output in faulty. Replace them now!.
- Engine Control
Module - OBD Error Code P00AC can also be due
to faulty ECMs which can store wrong error code
due to electrical problems. Better to get the faulty
electricals replaced as soon as possible.
- Powertrain Control
Module - Faulty powertrain can make car go
into failsafe mode, diminishing the vehicle’s overall performance. Find all the
Powertrain related parts with us.
- Diagnostic Tool - In order to detect the error, one needs high grade
diagnostic tools. Buy quality scanning and diagnostic tools for us today.
Symptoms Of OBD Error Code P00AC
No noticeable symptoms of a P00AC code can be
detected other than an MIL (Malfunction Indicator Lamp). However, an emissions
test can be done and it may reveal higher NOx readings depending on the type of
IAT failure. The engine may also stall under load, depending on the level of
sensor or circuit failure
How To Correct P00AC Intake Air Temperature Sensor 1 Circuit Low Bank 2
There are some direct indications to the
problem for P00AC error. These auto parts can be replaced first hand to solve
the problem and check if the error reappears.
- Replacement of the
Intake Air Temperature Sensor and circuit board
- Replacement or
reprogramming of the of the PCM
- Changing the
damaged and worn out wirings and harness
At Parts Avatar Canada buy top notch replacement parts for all makes and model like Mazda, BMW, Nissan, Audi, etc. and from top brands like Denso, Bosch and many more.
Easy Diagnosis Of Engine Error OBD Code P00AC
The step by step analysis and diagnosis is recommended by a
qualified technician using high grade diagnostic tools to check for all the
problems and solving them.
- You
require a scanner or a code reader and a digital volt ohmmeter to successfully
diagnose this code. Begin your diagnosis by visually inspecting all wiring and
connectors to the sensor.
- Search
for shorted or burned wiring and replace them.
- Connect
the scanner to the diagnostic connector and record all stored trouble codes and
freeze frame data. After the codes are cleared, operate the vehicle to see if
the code returns. If the code fails to immediately return, you may have an
intermittent condition.
- Check
for the problem with the IAT sensor and circuits and diagnose to see with the
error returns.
- If everything else is fine, then the problem can be with the PCM. Replace the PCM if required and check if the code reappears.
Common
Mistakes When Diagnosing OBD Code P00AC
Some of the common mistakes done while changing diagnosing
the OBD code P00AC are:
- Not
examining the IAT sensor failure
- Changing
the Powertrain Control Module (PCM) without checking other problems
- Not
checking for damaged or short wiring and connectors