P0089 OBD Error Code: Problem & Solutions

<<See All OBD Codes

A sudden increase in the fuel consumption and the engine performance along with occasional engine stalling and not starting with improper throttle response may be an indication of problem with the fuel pressure system hampering the engine’s performance, thus indicating OBD Code P0089.

The ECM commands FPR cycling, depending on demand, to modulate the fuel rail pressure. The ECM commands a lower FPR cycle to increase the fuel pressure. If less pressure is required, the ECM commands a higher FPR cycle. The ECM uses the fuel rail pressure sensor to continuously monitor fuel pressure. If the ECM detects a problem, such as an unexpected increase or decrease in fuel pressure, or excessive or insufficient fuel pressure, that is, higher or lower than commanded, it will set diagnostic trouble code P0089 – “Fuel Pressure Regulator 1 Performance,” and illuminate the malfunction indicator lamp (MIL).

What causes problem of Fuel Pressure Regulator 1 Performance?

• Fuel pressure regulator failure
• Fuel filter or screen clogged
• Fuel lines restricted or blocked
• Fuel pump faulty/damaged

1. Fuel Pump - Faulty fuel pump will not be able to meet the demand and thus affect the fuel delivery system and engine performance. Thus, replace faulty pumps now!
2. Fuel Filter - Clogged or damaged fuel filters will affect the fuel pressure system and hamper the performance. Replace them immediately when found faulty.
3. Diagnostic Tools - It is important to use the right diagnostic tools to correct the OBD code errors. Buy quality diagnostic tools from us.
4. Fuel Pressure Regulator - Faulty regulators is unable to determine the fuel requirement and hamper the fuel delivery system. Replace the damaged one now!

Depending on the make and model, the driver may experience many drivability issues and undesirable problems. The most obvious sign is the illumination of the Check Engine light on the dashboard. Other common symptoms include:

• Hard starting and engine stalling
• Poor acceleration or lack of engine power
• Reduced fuel economy
• Lean or rich conditions

• Replace or repair damaged or restricted fuel lines
• Replace faulty Fuel pressure regulator
• Replace clogged screens and filters
• Fuel pump replacement
• Replacement of fuel pump relay
• Repairing leakages
• Inspect PCM for faults

At Visit Parts Avatar Canada, find quality replacement and performance parts that are needed to correct the problem related to code P0089.

Qualified mechanics start their diagnosis by hooking up their advanced level scan tool to the PCM. Any error code present will have its own freeze frame data, which includes any info that tells mechanic what circumstances triggered the PCM to set the code. This includes information about the vehicle’s speed, RPM, coolant temperature, etc.

Then, the codes will be cleared and the vehicle will be taken for a test drive.

• With your OBD-II scan tool set, show ECM commanded fuel pressure and actual fuel pressure, engine rpm, fuel temperature, and fuel level. Check for fuel pressure readings at different times with Key On Engine Off, while cranking, at engine idle, or under load. Check these in comparison with expected values.
• If fuel pressure is too high, suspect areas include, faulty fuel pressure regulator, fuel return line restriction, clogged fuel injector. If fuel pressure is too low, suspect areas include, faulty fuel pressure regulator, restricted fuel filter, faulty supply pump, leaking fuel injector, worn mechanical pump or cam, or fuel leak.
• Next, check for any obvious problems in the wire harness, such as chafed wires, loose connectors, bent pins, backed-out pins, or corrosion. Repair as necessary and make sure all connectors are properly seated.
• Check fuses and relays for proper installation and continuity and repair as needed.
• With a DVOM, check for constant power or ground. Lacking proper power or ground, diagnose and repair as needed.
• Disconnect the ECM and FPR and check for continuity between the two connectors and repair as necessary.
• Also check for faults in the PCM (Powertrain Control Module) the replace or reprogram them as necessary.

Common Mistakes When Diagnosing The P0089 Code

Common mistakes are easy to make when performing diagnosis. They happen when steps are not followed in order or are skipped completely.

• Although a faulty/failing fuel pump is the most common cause for this OBD error, proper tests must be performed on the fuel pump before it is condemned and replaced.
• Always check for open, short or corroded wirings and connections to the sensors and components as it can also be the cause of the OBD error and can be a much cheaper diagnose to the problem.