P006B - OBD Trouble Code

<<See All OBD Codes

It can be very problematic if out of a blue moon you start facing problems with your exhaust pressure sensor, your car mechanic telling you to replace your mass airflow sensor or watching faulty powertrain control module. There are chances that the Generic Code P006B would soon flash up.

Do you wish to learn something more about error code P006B? Then you have arrived at the correct place. The P006B code would start triggering if some sort of discrepancy has been detected by the powertrain control module while correlating signals between the manifold absolute pressure sensor and the EPS. EPS stands for exhaust pressure sensor.

What causes this problem with Map - Exhaust Pressure Correlation?

• The exhaust pressure sensor may start malfunctioning
• Some defects may arise in mass airflow sensor
• Poor engine wiring to the exhaust pressure sensor and mass airflow sensor
• The powertrain control module may appear faulty or there are some chances that it may not have been tuned properly
• inoperative manifold absolute pressure sensor
• The wiring or connectors may be opened or shorted
• Faults in the engine computer
• Issues with the aftermarket air intake systems

1. Exhaust Pressure Sensor - Powertrain Control Module is perfectly fine but still but having that trouble code P006B flashing? In such a situation your Exhaust Pressure Sensor might be faulty. Why don’t you think of getting that replaced?
2. Mass Airflow Sensor - Common cause behind this P006B error code can be some fault in Mass Airflow Sensor. So, it will be a good decision to replace them now.
3. Exhaust System - Issues with the exhaust system can increase if not taken care of. So that’s why you must replace your damaged exhaust system parts online.
4. Powertrain Control Module - P006B code does not really end up spoiling your engine control module, but it might also accompany few powertrain control module issues. We have best powertrain related parts with us.
5. Mass Airflow Sensor Wiring - Are you facing OBD Error Code P006B? Don’t worry as you can fix this issue with new Mass Airflow Sensor Wiring. We care for our customers, that’s why we have Mass Airflow Sensor Wiring for every make and model.
6. Exhaust Pressure Sensor Wiring - The P006B code can also arise due to some issues in Exhaust Pressure Sensor Wiring. So, it is advised to replace them as soon as possible.
7. Diagnostic Tools - Are you searching for top quality auto diagnostic tools to get your car problems pointed out easily. Don’t worry as we are here to help you out.

We care for our customers and that’s why we can totally understand your problem. That’s the reason why we have listed out some major symptoms behind the flashing up of OBD Code P006B. They are mentioned here as follows:

Common Symptoms

• An illumination in the check engine light
• Excessive smoke may start pouring out from the exhaust poor engine performance
• Poor overall fuel economy
• The exhaust condition may be rich or lean
• Failsafe mode of the engine limp mode
• The car engine may die
• It may become hard to start the engine
• You might start facing engine stall issues

Want to correct the Trouble Code P006B? Read these points mentioned below:

• The exhaust pressure sensor should be replaced
• Make sure to replace the faulty Mass Airflow Sensor
• Repair or replace wiring to the exhaust pressure sensor and mass airflow sensor
• The Powertrain Control Module should be tuned to proper specifications
• Replace the defective Powertrain Control Module 

But you face any issue then you must visit us. We have stocked a wide range of best priced PCM, Exhaust System, Manifold Absolute Pressure Sensor and a lot more to help you out in fixing your car.

It is very important to have an access to a diagnostic scanner, a digital volt/ohmmeter (DVOM), and a reliable vehicle information source before you start diagnosing P006B error code. You must carefully check all related wiring and connectors visually. Make sure to pay close attention to wiring harnesses as well as connectors which are routed near hot exhaust components and the sharp edges associated with exhaust shields. If you find out any sort of damaged or burned areas, then you must make the required repairs. The next thing which you should do is to connect the scanner to the vehicle diagnostic port and retrieve all stored codes and freeze frame data. This would help a lot in the diagnosis. Then later you must clear the codes and test-drive the vehicle to see if the code is reset. Use the DVOM to test for reference voltage and a ground at the MAP and exhaust pressure sensor connectors.