Guide To P0025 OBD Error Code Solutions
OBD Code P0025 - Camshaft Position Timing Over Retarded Bank 2
Do you notice your car oil getting
dirty? Are you experiencing some problems with the Variable valve timing
circuit or some faults in the Oil control valve circuit? All these are probable
signs of OBD Code P0025.
Trouble code P0025 is related to camshaft position timing over retarded bank 2
Learn More About OBD Error Code P0025
The P0025 generic code starts
appearing when the engine control module has determined that the exhaust
variable camshaft timing for bank 2 is more retarded than what the car ECM has
actually commanded it to be. This condition of the over retarded timing can be
during the retarding or we can say during the advancing of the exhaust camshaft
timing.
What causes this problem with the Camshaft Position Timing
Over Retarded?
- The car oil may become dirty
- Variable valve timing circuit may be
opened or shorted
- Oil control valve circuit might be
opened or shorted
- Faults in the variable valve timing
- Defects in the oil control valve
- Engine control module might get
damaged
- Engine oil level might be too low
Replace/Repair These Parts To Fix OBD Code P0025
- Variable Valve
Timing - Damaged VVT can be a major reason why P0025
code depicts. So, make sure to replace it online so that you don’t have to face
any further issues.
- Oil Control Valve - Are your Oil Control Valve damaged or
broken? Don’t worry as we have solutions for all your problems.
- Engine Control
Module - Common cause
behind this P0025 error code can be some fault in Engine Control Module. So, it
will be a good decision to replace them now.
- Variable Camshaft
Timing - Issues with
Variable Camshaft Timing can be irritating and its best to replace them. We
have a huge variety of Variable Camshaft Timing available for our dear
customers.
- Camshaft Sensor - Some sort of defects in the Camshaft
Sensor can be a huge reason behind the appearance of P0025 code. So, you must
get it fixed.
- Crankshaft Sensor - Facing issues with crankshaft sensor
harness? Buy new crankshaft sensor harness and get rid of this issue.
Symptoms Of OBD Error Code P0025
Have a look at some of the most
common symptoms of P0025 error code below:
Common Symptoms
- Check engine light would be
turned ON by ECM if the camshaft timing is in a lower timing position than
expected
- It may be hard to start the engine
from the retarded timing position
- The engine may start running roughly
and the overall power would be reduced
- Drivability symptoms may start varying and it all depends on how far the camshaft is out of position
- Excessive emissions would be faced
by the engine from the tailpipe and fail emission testing
How To Correct P0025 "B" Camshaft Position - Timing Over-Retarded (Bank 2)
- Try to clear the fault codes and you can also
perform a road test to try and verify the failure
- Try to change the engine oil and filter to the
proper oil viscosity
- You must repair or replace the wiring or
connection to the camshaft oil control valve
- The camshaft oil control valve for bank 2 intake
camshaft should be replaced
- Replace camshaft phaser
for the bank 2 camshaft
Facing such issues? All you have to
do is to visit us as we have stocked a wide range of best priced replacement parts, ECM/PCM parts and a lot more to help you out in fixing your car.
Easy Diagnosis Of Engine Error OBD Code P0025
- Make sure that you visually check
all the electrical connections and wire harness to the camshaft sensor, oil
control valve and the crankshaft sensor for any issues that may cause the
problem
- Clear the code and verify if the
code returns
- Before you start performing any sort
of further testing, you must clear the code and verify if returns again or not
- You must carefully inspect if the
engine oil is clean and is of the correct viscosity
- The OCV should be commended to 100%
duty cycle to check if the camshaft timing changes
- Manufacturer's
specific pinpoint test should now be performed
Common
Mistakes When Diagnosing the P0025 Code
Generally, the people replace the
system sensors and the PCM in error, but actually the issue is with timing
alignment.
- Before you start to perform any sort
of repair or replacing the components, you must always verify the failure code
first.
- Verify the failure code is present
before doing any repairs or replacing of components.
- Visually check the problems with the
variable camshaft timing system components and wiring or connections.
- If you want to isolate the failure on the system, then you must follow the pinpoint test step-by-step
- The parts should only be replaced if
directed by the pinpoint or visual testing