Learn All About Car's Engine Oil Hardware

Engine oil is used for lubrication of internal combustion engines. The main function of engine oil is to reduce friction and wear on moving parts and to clean the engine from sludge. Engine oil or engine lubricant oil is made up of base oils enhanced with various additives, particularly antiwear additives. Engine oil creates a separating film between surfaces of moving parts to minimize direct contact between them, reducing heat and wear caused by friction, thus protecting the engine. Engine oil transfers heat through conduction as it flows through the engine making the engine cool.

The Society of Automotive Engineers (SAE) has established a numerical code system for grading engine oils according to their viscosity. Because of the viscosity of oil changes with temperature. This is why you would see something like this SAE 5W-30 on its packing. The numbers represent the viscosity of the oil and the W stands for WINTER. The lower the number, the thinner the oil and the better the oil's cold start performance. The number after the W describes how thick the oil is at the engine’s normal operating temperature.

Engine oils consist of rust & corrosion inhibitors that provide protection against regular wear & tear. It helps in reducing friction and removes impurities. Engine oil acts as a coolant. It acts as a gap filler between parts.

Using the correct oil keeps an engine running smoothly. It creates a thin, lubricating layer between metal surfaces. Due to its thickness and viscosity, it sticks to the engine components reducing wear and tear of the engine. Engine oil lubricates rotating or sliding surfaces between the crankshaft main bearings and big-end bearings and rods connecting the pistons to the crankshaft. The oil is collected in an oil pan, or sump, at the bottom of the crankcase. The oil pump takes oil from the oil pan and sends it through the oil filter into oil galleries, from which the oil lubricates the complete engine. In modern designs, there are also passageways through the rods which carry oil from the rod bearings to the rod-piston connections and lubricate the contacting surfaces between the piston rings and cylinder.

A car runs for thousands of miles; therefore, it is subject to wear and tear. The most common problems are linked to engine oil. Getting the engines checked for engine oil-related problems is always necessary. Any delay with oil-related problems will increase expenses. Low engine oil in the system due to leakage, the wrong number of oils used, low viscosity in used oil. Engine oil getting burnt due to piston rings or oil ring damage. An engine that burns oil will usually foul the spark plugs. That, in turn, will cause ignition misfire, higher emissions are likely to damage the catalytic converter. Heavy engine oil leakages can also damage the engine. These are some of the common problems.

There are not many tools required to change the engine oil. Changing your car engine oil is very easy. You should have the correct tools for this job and understand how to perform an oil change. You may need the following tools.

• Basic Socket Wrench
• Funnel
• Tool To Remove The Oil Filter
• Oil Drain Pan
• Hydraulic Jack

Most of the people have a nature to avoid risk and seek safety. That is the reason why they would go with a familiar auto parts brand than a new one. It would prove to be safe and they know what to expect. Have a look at our top brands for Engine Oil Hardware.

If you are like most of us, then you won’t know much about the related components of car Engine Oil Hardware. Fear not! Here is a quick and easy guide to explain the related parts of the Engine Oil Hardware.

• Engine Temperature Sensor Connector
• Manifold Heater Relay
• Engine Shutdown Connector
• Engine Oil Filler Cap
• Engine Oil Stand Pipe
• Engine Stabilizer Bushing
• Oil Cap

As there is not much to be repaired in this system and the process to change engine oil is very easy so the labor cost automatically gets cheap. Because all you have to do is just open a drain plug bolt. It takes about 30 to 40 minutes for the whole process. Labor costs are about $200 to $ 300. Engine oil could range from $10 to $15 for one liter.

Not all of us get to service our own cars. In fact, most of us don’t even know what is under the hood of our car, that’s why car service centers and mechanics are there. But changing engine oil is pretty simple. All you have to do is the following. Check the oil and oil filter that is recommended by your vehicle's manufacturer. Also, check the quantity of oil required. Run your engine for about 5 minutes. Secure your car in a flat, stable, and even platform and raise it with the help of hydraulic jack. Drain the old engine oil in the oil pan by removing the oil drain plug. Allow it several minutes to completely drain the oil from the engine. Most of the drain plug has magnets make sure to clean it. Remove the oil filter and clean the surface holding the filter. Place the new oil filter. Tighten the drain plug. Add new engine oil from the top of the car with the help of a funnel. A dipstick can be used to check the level of oil in the engine if all is well then, start your car and let it run for a few minutes in the meanwhile check for any leakages. Switch off the car engine and check the oil level after five minutes. On the dipstick, it should be on the max mark. Make note of the kilometers run at the time of engine oil change. Manufacturers recommend changing oil and oil filter every after 7000 to 10000 kilometers.