Dodge Ram 2500 Suspension Parts

The suspension holds the wheels in direct contact with the ground for stability, turning, and braking, which enables the transfer of power to the ground, increasing balance and control. Every suspension system has springs to handle bumps and shock absorbers to manage spring movement. There are several types of suspension systems and can be categorized into solid (beam) suspension axles and independent suspensions. In the case of a solid axle suspension, the wheels on either side of the vehicle are bound by a rigid axle frame, and the bump in the road that affects one wheel will also affect the wheel on the other side. Solid axles may be live axles that transfer power to the wheels or dead axles like the rear axle on the front-wheel drive. As the term suggests, independent suspensions allow the wheels to travel independently of each other, and the impact of a bump on the road experienced by a single wheel will be confined to that wheel and will not influence the wheel on the other side of the vehicle. Independent suspensions use either a strut or a shock absorbers. A strut is a shock absorber that is often used as a suspension aid. The most common type of strut suspension is the MacPherson strut, which consists of a shock absorber, spring, and suspension in one unit. When used at the front of the automobile, the upper steering pivot is at the top of the strut. Shock absorbers are used for the stabilization of the control arm. Shocks and struts are the most widely used suspension components. Since they deteriorate steadily and decrease handling and ride efficiency, it is advised that they must be replaced after 50,000 miles, and earlier if you encounter a bouncy ride, a nosedive while accelerating, and an excessive body roll in turns.

Leaf springs are the oldest type of suspension springs and are commonly used to suspend live axles. They are used in vehicles for hauling and carrying huge loads, and their capacity can be increased by adding more leaves to the springs. Coil springs are the most popular types of spring used today. They are much easier to tune for specific riding and/or handling, making them suitable for performance vehicles. A torsion bar is a spring that twists in response to the movement of the wheel. The benefit of torsion bars is that they can be adapted to correct the ride height of the vehicle. Air suspension springs use compressed air to ensure a smooth ride and they are equipped with suspension leveling and self-leveling sensors that provide a ride height signal to the air suspension control module. The wheels, springs, and shocks and struts are attached to the vehicle using the suspension member called control arms. Control arms are known by different names depending on the suspension systems and where they are located on the vehicle, like short and long arms, radius arms, and trailing arms. They are generally made of stamped steel or aluminum and are articulated by means of bushings and ball joints. The control arms are very durable and are replaced when bent, but the bushings and ball joints wear and require replacement to mitigate play that can affect the handling and alignment angles. Incorrect alignment angles can cause tire pull and tire wear. If the traditional methods of adjustment are inadequate, the alignment kit can provide angles within the specification. The steering knuckles are the connecting point for the front wheels, the suspension, and the steering link. The wheels are attached to spindles that form an integral part of the knuckle. Ball joints enable the knuckles to move up and down with the suspension movement and then pivot in response to the steering input. Panhard rods and track bars are located laterally within the body of the vehicle and avoid side-to-side motion. Sway bars are torsion bars that link the wheels on both sides of the vehicle to minimize the body roll.

If the suspension parts are faulty, then the vehicle will make noise and start pulling towards one side. PartsAvatar offers the largest array of the suspension parts to all your auto parts needs and offers parts from the famous brands and manufacturers, to make sure you get top quality parts. We also offer the lowest prices in the market and free delivery* options as well. We deliver all parts from our fulfillment centers situated across Canada in places like Vancouver, Edmonton, Montreal, and Toronto.

Are you looking for suspension parts at a good price? No matter what the suspension parts requirements are, we’re ready to help you out. We at PartsAvatar have a wide range of suspension parts in stock, specific to each car. If you need one for your car, then all you need to do is to choose your car year, make and model from the menu at the top left. If you have a preference for a specific manufacturer, you can also make a selection for it. You can also find the correct part in the search bar. Once you are sure that you have made the selection for the right fitment, then you can choose the respective part you need and make a final purchase.

PartsAvatar brings you the auto parts at the best prices without compromising on quality brands. We source our parts from famous and leading brands, for example, Mevotech, Mevotech TTX, Moog, Transit Warehouse, Dorman (OW Solutions), Mevotech Original Grade, and many more. We offer handpicked quality suspension parts to ensure that we have only the top manufacturers in each line of auto parts. Now there is no need to do a trade-off between a premium quality part and the one that is fairly priced. All parts come with specific brand warranties and even claim to be superior to OEM parts!