Know More About Auto Driving & Fog Lights

Driving Light

A great addition to the high-beam headlights are the driving lights which are already there in our motor vehicles. If you would switch on an extra set of lights, then it would surely brighten up the way ahead. This additional forward illumination can turn out to be magnificent, especially if a motor vehicle’s driving lights would be high powered.

Fog Light

The front-facing fog lights and fog lamps are a type of automotive headlight which would be designed to emit light in a bar-shaped beam. The beam would be designed typically to have a sharp cut off on the top, and the actual lights would be generally installed low and aimed toward the ground at a sharp angle.

Are you searching for the different types of driving & fog light? Then don’t worry! All you have to do is to have a look below and then all your doubts regarding its types would be cleared.

Fog Light

• Fog lights come in various types from the factory. The main types you’ll find are:
• HID (white, yellow, or blue)
• LED (white or blue)
• Halogen (white, yellow, or blue)

HID Fog Light

• LED Fog Lights: OPT7 LED Fog Lights
• Yellow Fog Lights
• Blue Halogen Fog Lights

Are you searching how do the driving & fog light actually work? Then all you have to do is to have a look below and then you will be able to understand everything.

The front fog lights would be only really of any use in extremely poor visibility. Now in such a situation, even the normal low beam lights would reflect off the fog in front.

The proper front fog lights would be mounted low down on the bodywork and would be angled down at a steeper angle than normal headlights. The pattern of the beam would be wide and flat, with a distinct cutoff at the top-this would reduce the amount of light which would be reflecting off the fog. When the low-beam lights would be switched off, then the fog lights can be used by the driver to illuminate the road which would be directly in front of them, so they could proceed at low speed.

There are a lot of front fog lights which are nowadays of little practical use and at the same time would be poorly designed. They would be more styling feature than anything useful. If you see a car coming the other way with fog lights blazing in clear weather then it would be a sign of an approaching prat though.

The rear lights are an intense red light, which are the same in brightness to a brake light. They are utilized to increase the visibility of your automobile to those which would be approaching from behind. Just keep in mind that they should be switched off when following vehicles are would be actually present to avoid excessive glare.

The fog lights which would only light the ground immediately in front of your car, would be mainly for very foggy conditions when you would be travelling slowly because of limited visibility. They can also be sometimes utilized on dark windy roads in the middle of the night. On a sunny day, you will likely not even observe your fog lights, and there would be no purpose of using them during these times.

There are a few things which might cause your driving & fog light to malfunction. Watch for the following symptoms if you suspect a bad driving & fog light:

Fog Lights Are Dim Or Flickering

One of the most common symptoms of some issues with the fog light bulbs are fog lights which would be dim or flickering. If you find out that the fog lights are starting to shine more dimly than normal or flicker when they would be turned on, then it could be a symptom that the light bulbs are worn.

Fog Lights Do Not Turn On

One another symptom of some issues with the fog/driving light bulbs would be that the fog/driving lights would not turn on. If the bulb would start breaking or the filament would wear out due to some reason, then it would leave the fog lights without functioning bulbs. There would be a need to replace the broken or non-functional bulbs to so that the functionality to the fog lights can be restored.

If you want to repair, you’re Driving & Fog Light all by yourself, then let’s face it that you will need some auto body tools. You can always start by building your own tool chest. Searching for some tools needed to repair you’re Driving & Fog Light? Don’t Worry! We are here to help you out. Here are some common tools that you will probably end up needing while repairing you’re Driving & Fog Light.

• Screwdriver set
• Socket set
• Allen wrench set
• Torx wrench set

If customers trust a brand, then it would make them loyal, and if they are loyal, then they will surely buy more. We are well aware that customers want comfort, cheerfulness as well as satisfaction in their lives and that’s the reason why we offer top quality auto parts brands to our customers. We make sure to provide a positive experience to our consumers from the brands which we are offering so that they can form an opinion that a particular auto parts brand is trustworthy and would give them peace of mind while they are purchasing it for their car. Here we have listed out some top brands for Driving & Fog Light.

We learn more by looking for the answer to a question. That’s the reason why we are here to provide you the answers for all your questions. Thinking about the related parts of the car Driving & Fog Light? Fear not! Just have a look below: -

• Fog Light Assembly
• Mount Kits
• Fog Light
• Fog Light Socket
• Driving Light
• Driving Light Assembly
• Daytime Running Light

More than any other kind of failure in a car, there's almost nothing that's quite as heartbreaking as a completely damaged Driving & Fog Light. Now when we talk about the replacement cost, it might vary a lot even on the same car depending upon its performance, labor cost, brand etc.

Do you want to change your driving & fog light on your own? Then have a look at the steps of changing the driving & fog light below:

Method 1 of 2: Changing fog or driving light bulbs integrated into the front bumper

Step 1

First of all you should identify fog or driving light bulb which has to be replaced. Then you should turn the fog or driving lights on.

It might be important to turn the ignition key to the “run” position before the lights would come on. Then you should walk around to the front of the vehicle and then you should make a note of which light has to be replaced.

Step 2

Then you should remove fog or driving light bulb from the back of the housing. Then you should gain access to the back of the housing on the desired fog or driving lights.

It might be essential to get to the bulb from the top in the engine bay or from the bottom, as it all depends upon which bulb is being replaced as well as its mounting position. Then you should gently turn the bulb ¼ to ½ turn counter-clockwise, and then you should gently pull out to separate the bulb from the housing.

Step 3

The electrical connector should then be disconnected from the fog or driving light bulb. It would be generally accomplished by squeezing the lock tab and then the plug should then be pulled gently from the bulb.

Step 4

Then it is essential to confirm if the replacement fog or driving light bulb would be correct. The replacement fog or driving light bulb should then be visually inspected.

It should then be compared to the bulb which has been removed so that you are sure that it is the right replacement. There are a lot of bulbs which would have a model or type number around its base.

Step 5

The replacement bulb should then be installed into housing. It would be generally easier to get the bulb installed back into the housing before plugging the electrical connector back into the bulb.

Note: Fog as well as driving light bulbs can generally be installed in one certain orientation. The tabs would only line up one way before you would be able to turn it the ¼ to ½ turn so that it can be locked into the position.

Warning: It is the halogen bulbs which would operate at very high temperatures. It would be very essential not to touch the glass on the bulb, as it would deposit oil from your hand onto the glass which can cause a “hot spot” and the bulb would start failing prematurely. If the contact would be made, then you should clean the glass with alcohol or another suitable degreaser. The bulb should then be allowed to dry completely and then reinstall.

Step 6

The electrical connector should then be plugged in. The electrical connector should then be plugged back into the bulb, and you should pay attention that the orientation should be correct and that the connector should seat fully.

Now once the connector would be seated completely, then the retaining tab should be allowed to engage.

Step 7

The function of replacement fog or driving light bulb should then be verified. Then you should turn the ignition key to the “run” position.

The fog or driving lights should then be turned on. Then you should go to the front of the automobile and then check that the replacement bulb is operating.

Step 8

Everything which has been removed should then be reinstalled properly. Now once the replacement would be successful, then you should reinstall anything that was removed in order to access the fog or driving lights.

Method 2 of 2: Replacing a fog or driving light bulb on self-contained units

Step 1

Firstly, you should identify fog or driving light bulb which has to be replaced. Then the fog or driving lights should be turned on.

There might be some need to turn the ignition key to the “run” position before the lights would start coming on. You should then walk around to the front of the automobile and then a note regarding which light should be replaced should be made.

Note: There is some latest fog or driving lights which utilize a type of bulb which would need using the procedure in method 1 above. In method 2, we would focus on the sealed beam type of bulb.

Step 2

The retaining/trim ring should then be removed from front of fog or driving light housing. The face of the fog or driving lights would be held on with any number and type of fasteners.

It can be any number of screws, bolts, or nuts which should be removed so that an access to the bulb can be gained.

Warning: Just be sure that the ignition switch has been turned off and the switch should be in the off position. There is some fog as well as driving light systems which would work on a high voltage system and an accidental shock from these systems could result in bodily injury.

Step 3

The bulbs should then be separated from the housing. Now at this point, the sealed beam might also become loose, so be sure that it should not drop out of the housing and break.

Step 4

The electrical connector should then be unplugged. There are some sealed beam fog and driving light bulbs which would use a connector with a retainer on it, and there are others which would use a push on fitting or static fit connector.

Step 5

The replacement bulb should then be compared to the one which has been removed. Just be sure that it should be of the same diameter and has the same number of connector pins, and should be of the same layout as the original.

Step 6

The electrical connector should then be plugged into the replacement bulb. Just be sure that you should seat the connector all the way down onto the terminals.

If there would be a retaining tab in the connector, then you should be sure that the retainer should be engaged when installed.

Step 7

The replacement fog or driving light bulb should then be installed into housing. Just be careful that you should not pinch the wiring between the bulb and the housing during the process of reinstallation.

Step 8

Then the next step would be to install the fog or driving light retaining bezel. While holding the fog or driving light bulb in place inside the housing, the bezel should be placed back onto the face of the fog or driving lights.

Once the bezel would be back in position, then you should hold everything in place by the bezel while you reinstall the retaining hardware.

Step 9

The operation of replacement fog or driving light should then be verified. Now when everything would be reinstalled, then the ignition should be turned to the “run” position and turn the switch on for the fog or driving lights.

You should then walk around to the front of the vehicle and then it should be verified that the lights would not be working properly.